Updated Nov 22, 2026· 9 min read

Our Top Picks

  1. 50 Pcs 3D Printer Nozzles Hardened Steel Stainless
    Check on Amazon
  2. Comgrow 25PCS MK8 Ender 3 V2 Nozzles 0.4MM
    Check on Amazon
  3. XIFOWE MK8 Nozzles 24 pcs Assorted Sizes 3DMK8 Brass
    Check on Amazon
  4. 8Pcs 3D Printer Upgraded Hardened Steel MK8 Nozzles
    Check on Amazon
  5. 4pcs Hardened Steel Nozzles M6 Nozzle 0.25/0.4/0.5/0.6mm Compatible1x0.25+1x0.4+1x0.5+1x0.6mm
    Check on Amazon

The nozzle is the smallest part of an FDM printer and the one that decides what a print looks like. A 0.2 mm opening lays down the fine lines that keep a 28 mm miniature’s face, weapon, and armor trim readable, while a 1.0 mm opening pushes out a terrain wall or a chunky prop in a fraction of the time. The standard 0.4 mm sits in the middle and handles most gaming parts well, which is why every kit below is heavy on 0.4 mm spares.

Our top pick: Axeyil 50-Piece Mixed-Material MK8 Nozzle Kit. Runner-up: Comgrow 25-Piece 0.4 mm Brass Nozzle Kit.

Material matters as much as size. Brass is the default for PLA and ABS: it heats evenly, costs little, and wears slowly on plain filament. Abrasive filament changes the math. Carbon fiber, glass fiber, and glow-in-the-dark blends chew through a brass bore in a few prints, widening the opening and blurring detail. Hardened steel resists that wear, which is why two of the five picks below are hardened steel sets.

One warning before the list: MK8, V6, and Volcano nozzles are NOT interchangeable. All three use the same M6 thread, so a wrong-family nozzle will screw into your hotend and then print badly or not at all. Match the nozzle family to your hotend first, then pick a size. Every pick below names its family, and the How to choose section explains the differences.

As an Amazon Associate, we earn from qualifying purchases.

How to choose a 3D printer nozzle for gaming prints

Diameter sets the detail-versus-speed trade. A 0.2 or 0.25 mm nozzle lays the finest layers, which is what miniature faces, small text, and thin armor edges need. A 0.4 mm nozzle is the everyday standard: fine enough for most minis, fast enough for terrain, and the least likely to clog. A 0.6 or 0.8 mm nozzle prints big parts and terrain much faster with stronger layer bonds, at the cost of visible layer lines. A 1.0 mm nozzle is for rough structural prints where speed matters more than surface finish. Smaller openings clog more easily, so keep cleaning needles handy if you print below 0.3 mm.

Material follows your filament. Brass is the right call for PLA, ABS, and PETG. Hardened steel is the right call for anything abrasive: carbon fiber, glass fiber, glow-in-the-dark, and metal-filled blends. Stainless steel sits in between and shows up in one kit below. Hardened steel trades a little thermal conductivity for wear resistance, so expect to run it at the upper end of your filament’s temperature range.

Family is the fit check that matters most. MK8 nozzles are short and fit Ender 3, Ender 5, and CR-10 style hotends. V6 nozzles are longer and fit Prusa i3, Anycubic, and Vyper style hotends. Volcano nozzles are longer still, with a bigger melt zone for high-flow printing. Same M6 thread, different lengths — never swap families. Also check the printer model, not just the family: the Ender 3 V3 uses a different hotend from the Ender 3 V2, and the Neptune 4 series differs from the Neptune 3. Bambu Lab A1 owners need a complete hotend assembly, not a bare nozzle, so no Bambu pick appears here.

Kits versus single-size packs. A multi-size kit is the way to learn which diameter you actually use, and the 0.4 mm spares inside it cover everyday printing. A single-size bulk pack is the better buy once you know 0.4 mm is your size — a clogged nozzle mid-print is a five-minute swap instead of a ruined evening. Swap nozzles while the hotend is heated to printing temperature, holding the heater block steady with a wrench, and always confirm the new nozzle seats fully before printing.

1. Axeyil 50-Piece Mixed-Material MK8 Nozzle Kit

This is the full-drawer option: 45 nozzles plus tools in one box, covering brass, stainless steel, and hardened stainless steel across the whole useful size range. The brass count is 30, with two each of 0.1, 0.2, 0.3, 0.5, 0.6, 0.8, and 1.0 mm plus sixteen 0.4 mm nozzles, so the workhorse size is well stocked. Eleven stainless steel nozzles and four hardened stainless steel 0.4 mm nozzles cover tougher filament. The 0.1 mm brass nozzle is the finest opening in this lineup. The kit also includes curved and straight tweezers, an L wrench, an open-end wrench, five cleaning needles, and a brush. It fits MK8 hotends on CR-10 and Ender 3 printers.

Specs

    • 45 nozzles plus tools (50 pieces total)
    • Brass: 30 nozzles (0.1, 0.2, 0.3, 0.5, 0.6, 0.8, 1.0 mm ×2 each; 0.4 mm ×16)
    • Stainless steel: 11 nozzles (0.4 mm ×8, 0.5 mm ×2, 1.0 mm ×1)
    • Hardened stainless steel: 4 nozzles (0.4 mm)
    • MK8 family; fits CR-10, Ender 3
    • Tools: curved and straight tweezers, L wrench, open-end wrench, 5 cleaning needles, brush
    • Model AQ-553

    2. Comgrow 25-Piece 0.4 mm Brass Nozzle Kit

    If 0.4 mm is your size — and for most gaming prints it is — this is the bulk buy: twenty-five identical brass nozzles, so a clog or a worn bore is a quick swap rather than a stalled print. The kit adds ten cleaning needles, a hex wrench, stainless tweezers, and a storage box that keeps the spares sorted. The listed diameter error is under 0.02 mm, and the nozzles take 1.75 mm PLA and ABS. Compatibility covers the Ender 3 family (including Pro, V2, Max, S1, S1 Pro, and Neo), the Ender 5 Pro, and the CR-10 series. Note the brand is Comgrow: the listing’s detail table names a different manufacturer, but the title and store are Comgrow, and that is the brand to look for.

    Specs

      • 25 × 0.4 mm brass nozzles
      • 10 cleaning needles, hex wrench, stainless tweezers, storage box
      • 1.75 mm filament; diameter error under 0.02 mm
      • MK8 family; fits Ender 3/Pro/V2/Max, Ender 5 Pro, Ender 3 S1/S1 Pro/Neo, CR-10 series
      • Kit weight: 5.3 oz

      3. XIFOWE 24-Piece Brass Nozzle Kit

      This kit splits the difference between the Axeyil drawer and the Comgrow bulk pack: twenty-four brass nozzles with sixteen 0.4 mm workhorses plus two each of 0.2, 0.6, 0.8, and 1.0 mm for detail and speed work. Ten stainless steel needles, a ten-grid parts box, and a 6 mm hex wrench come with it, and each nozzle has its size marked on the surface. The M6 thread is 5 mm long, and the compatibility list is broad across the CR-10 family and the Ender 2, 3, 5, and 6 families. The listing has been retitled since its 2022 version — the current title drops the brand prefix and adds the expanded compatibility — but the brand remains XIFOWE in the spec table.

      Specs

        • 24 brass nozzles (2×0.2, 16×0.4, 2×0.6, 2×0.8, 2×1.0 mm)
        • 10 stainless steel needles, ten-grid parts box, 6 mm hex wrench
        • M6 thread, 5 mm thread length; sizes marked on surface
        • MK8 family; fits CR-10 family, Ender 2, 3, 5, and 6 family
        • Model NZ-0

        4. Creality 8-Piece Hardened Steel MK8 Nozzle Set

        This is the abrasive-filament pick for MK8 hotends: eight black hardened steel nozzles in 0.2, 0.4, 0.6, 0.8, and 1.0 mm, confirmed on the current listing, which now titles the set as upgraded metal and lists model SV-BOZZLES. The listing describes the steel as hardened tungsten steel with hardness beyond HRC60 and a 450 °C maximum temperature, rated for PLA and ABS through carbon fiber and even PEEK. A DIY tools storage box is included. It fits MK8 heating blocks on the Ender 3 and Ender 5 series, CR-10 series, Sovol SV06, and Makerbot. The listing does not state how the eight nozzles split across the five sizes, so do not expect a published count per size. Two honest flags: the kit may not fit the Ender 3 V3, which uses a different hotend, and some owners report packs arriving without the advertised storage box or cleaning needles. The newest full listing capture is from 2022, but the set is current in October and November 2026 guides, so confirm availability on the live listing before ordering.

        Specs

          • 8 hardened steel MK8 nozzles (0.2, 0.4, 0.6, 0.8, 1.0 mm)
          • Hardened steel, hardness beyond HRC60; maximum temperature 450 °C
          • DIY tools storage box included
          • MK8 family; fits Ender 3 and 5, CR-10, Sovol SV06, Makerbot
          • Model SV-BOZZLES

          5. POLISI3D 4-Piece Hardened Steel V6 Nozzle Set

          The only V6 pick in this lineup, and the one to buy if your printer runs a V6 hotend: four hardened steel nozzles in 1×0.25, 1×0.4, 1×0.5, and 1×0.6 mm. The 0.25 mm nozzle is the fine-detail option for V6 owners printing miniatures, while the hardened steel handles carbon fiber, PEI, and PEEK filament that would wear out brass. Each nozzle is marked by a dot count on the body: 0.25 mm has 0 dots, 0.4 mm has 3 dots, 0.5 mm has 6 dots, and 0.6 mm has 4 dots — read the dots, not the packaging, when you swap. It fits V6 hotends on the Prusa i3 MK3S, Anycubic Mega S, and Vyper. It is V6 only: the M6 thread matches MK8, but the length does not, so it will not work correctly in an MK8 hotend. The newest full listing capture is from 2022, but the set is current in October 2026 guides, so confirm availability on the live listing before ordering.

          Specs

            • 4 hardened steel V6 nozzles (1×0.25, 1×0.4, 1×0.5, 1×0.6 mm)
            • Dot-marked sizes: 0.25 = 0 dots, 0.4 = 3 dots, 0.5 = 6 dots, 0.6 = 4 dots
            • M6 thread; V6 hotend only (not MK8)
            • Fits Prusa i3 MK3S, Anycubic Mega S, Vyper
            • 1.75 mm filament; PEI, PEEK, carbon fiber capable

            Quick comparison

            Pick Family Material Sizes Best for
            Axeyil 50-piece MK8 Brass, stainless, hardened 0.1–1.0 mm, 45 nozzles A full nozzle drawer in one box
            Comgrow 25-piece MK8 Brass 0.4 mm ×25 Bulk spares of the standard size
            XIFOWE 24-piece MK8 Brass 0.2–1.0 mm, 24 nozzles 0.4-heavy multi-size kit
            Creality 8-piece MK8 Hardened steel 0.2–1.0 mm, 8 nozzles Abrasive filament on MK8
            POLISI3D 4-piece V6 Hardened steel 0.25–0.6 mm, 4 nozzles Fine detail on V6 hotends

            FAQ

            What nozzle size is best for 3D printed miniatures?

            A 0.2 or 0.25 mm nozzle gives the finest detail on small miniatures, and the Axeyil kit’s 0.1 mm nozzle goes finer still for the smallest features. A 0.4 mm nozzle is the practical default: it prints most miniatures well with far less clogging risk and much faster print times. Use the fine nozzles for faces and display pieces, and the 0.4 mm for rank-and-file troops and gaming parts.

            Can I use an MK8 nozzle in a V6 hotend?

            No. MK8, V6, and Volcano nozzles share the same M6 thread, so they will screw in, but their lengths and melt zones differ. A wrong-family nozzle seats at the wrong depth, which causes leaks, clogs, and poor extrusion. Check your printer’s hotend family before ordering: Ender 3 and CR-10 printers use MK8, while Prusa i3, Anycubic Mega S, and Vyper printers use V6.

            Do I need hardened steel nozzles for carbon fiber filament?

            Yes. Carbon fiber, glass fiber, and glow-in-the-dark filaments are abrasive and wear out a brass nozzle quickly, widening the bore and blurring detail. Hardened steel nozzles resist that wear — the Creality set covers MK8 hotends and the POLISI3D set covers V6 hotends. For plain PLA, ABS, and PETG, brass is fine and heats more evenly.

            How often should I change a 3D printer nozzle?

            Change it when print quality drops: stringing, under-extrusion, rough walls, or inconsistent layer lines after a filament change are the usual signs. Abrasive filament shortens nozzle life sharply, while plain PLA can run through one brass nozzle for a long time. Keep spares on hand — a nozzle swap takes minutes with the hotend heated — and replace the nozzle rather than fighting a stubborn clog.

            Conclusion

            Start with your hotend family, then match the pick to your filament. The Axeyil 50-piece kit is the best single purchase for MK8 owners who want every size and material covered. The Comgrow 25-piece kit is the bulk buy for anyone who lives at 0.4 mm. The XIFOWE 24-piece kit is the middle path: mostly 0.4 mm with detail and speed sizes included. The Creality hardened steel set is the MK8 answer for abrasive filament, and the POLISI3D set is the V6 answer for fine detail and tough filament alike. Whichever you choose, confirm the family and the size on the listing before ordering — a nozzle that does not fit your hotend is a spare you cannot use.

            R
            Razer Gaming Series Editorial Team
            We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.

            FAQ

            What nozzle size is best for 3D printed miniatures?
            A 0.2 or 0.25 mm nozzle gives the finest detail on small miniatures, and the Axeyil kit’s 0.1 mm nozzle goes finer still for the smallest features. A 0.4 mm nozzle is the practical default: it prints most miniatures well with far less clogging risk and much faster print times. Use the fine nozzles for faces and display pieces, and the 0.4 mm for rank-and-file troops and gaming parts.
            Can I use an MK8 nozzle in a V6 hotend?
            No. MK8, V6, and Volcano nozzles share the same M6 thread, so they will screw in, but their lengths and melt zones differ. A wrong-family nozzle seats at the wrong depth, which causes leaks, clogs, and poor extrusion. Check your printer’s hotend family before ordering: Ender 3 and CR-10 printers use MK8, while Prusa i3, Anycubic Mega S, and Vyper printers use V6.
            Do I need hardened steel nozzles for carbon fiber filament?
            Yes. Carbon fiber, glass fiber, and glow-in-the-dark filaments are abrasive and wear out a brass nozzle quickly, widening the bore and blurring detail. Hardened steel nozzles resist that wear — the Creality set covers MK8 hotends and the POLISI3D set covers V6 hotends. For plain PLA, ABS, and PETG, brass is fine and heats more evenly.
            How often should I change a 3D printer nozzle?
            Change it when print quality drops: stringing, under-extrusion, rough walls, or inconsistent layer lines after a filament change are the usual signs. Abrasive filament shortens nozzle life sharply, while plain PLA can run through one brass nozzle for a long time. Keep spares on hand — a nozzle swap takes minutes with the hotend heated — and replace the nozzle rather than fighting a stubborn clog.
            Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
            Best 3D Printer Nozzles for Gaming Minis and…Check price on Amazon

            More from Amazon

            Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

            Amazon Prime

            Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

            Start a Prime free trial
            Amazon Music Unlimited

            Ad-free music streaming. Eligible new subscribers can start with a free trial.

            Try Music Unlimited free
            Prime for Young Adults

            A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

            See Prime for Young Adults
            Audible

            Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

            Try Audible free

            As an Amazon Associate we earn from qualifying purchases.